Este ejemplo compara las longitudes eficaces y el factor de carga crítica, que se pueden calcular en RFEM 6 utilizando el complemento Estabilidad de la estructura, con un cálculo manual. El sistema estructural es un pórtico rígido con dos pilares articulados adicionales. Este pilar está cargado por cargas puntuales verticales.
En el ejemplo de validación actual, investigamos el coeficiente de presión del viento (Cp) para las barras estructurales principales (Cp,ave) y las barras estructurales secundarias, como los sistemas de revestimiento o fachada (Cp,local) según NBC 2020 [ 1] y
Base de datos japonesa de túneles de viento
para un edificio de poca altura con una pendiente de 45 grados. La configuración recomendada para una cubierta plana tridimensional con aleros afilados se describirá en la siguiente parte.
En el ejemplo de validación actual, investigamos el valor de la presión del viento tanto para el cálculo estructural general (Cp,10) como para el cálculo estructural local, como el revestimiento o los sistemas de fachada (Cp,1) según el ejemplo de cubierta plana de EN 1991-1-4 [1] y
Base de datos japonesa de túneles de viento
. La configuración recomendada para una cubierta plana tridimensional con aleros afilados se describirá en la siguiente parte.
En el ejemplo de validación actual, investigamos el valor de la presión del viento para los diseños estructurales generales (Cp, 10 ) y el diseño de revestimientos o fachadas (Cp, 1 ) de edificios de planta rectangular con EN 1991-1-4 [1] . Hay casos tridimensionales de los que explicaremos más en la siguiente parte.
Una estructura hecha de un perfil en I está incrustada en los apoyos de la horquilla. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Una cercha plana que consta de cuatro barras inclinadas y una barra vertical está cargada en el nudo superior por medio de una fuerza vertical y una fuerza fuera del plano. Assuming the large deformation analysis and neglecting the self-weight, determine the normal forces of the members and the out-of-plane displacement of the upper node.
Una consola hecha de un redondo está cargada por un esfuerzo axil excéntrico. Determine the maximum vertical deflection of the console using the geometrically linear and second-order analysis.
Una consola hecha de un redondo está cargada por una fuerza transversal excéntrica. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Una consola hecha de un redondo está cargada por una carga uniforme excéntrica. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Una biela con una sección circular se apoya según cuatro casos básicos de pandeo de Euler y se somete a una fuerza de presión. Determine the critical load.
Este ejemplo de verificación se basa en el ejemplo de verificación 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Una estructura superficial simétrica se compone de ocho barras de celosía iguales, que están incrustadas en los apoyos de las articulaciones. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Una estructura se compone de cuatro barras de celosía, que están incrustadas en apoyos de articulación. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Consider an ASTM A992 W 18×50 beam forspan and uniform dead and live loads as shown in Figure 1. La barra está limitada a un canto nominal máximo de 18 pulgadas. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Determine la deformación máxima de la placa sin considerar el peso propio.
Un pilar se compone de una sección de hormigón (rectángulo 100/200) y una sección de acero (perfil I 200). It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Un anillo circular delgado de sección rectangular está expuesto a una presión externa. Determine the critical load and corresponding load factor for in-plane buckling.
Una viga curva consta de dos vigas con una sección rectangular. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Un recipiente cónico de paredes delgadas está lleno de agua. Thus, it is loaded by hydrostatic pressure. While neglecting self-weight, determine the stresses in the surface line and circumferential direction. The analytical solution is based on the theory of thin-walled vessels. This theory was introduced in Verification Example 0084.
Un oscilador simple consta de una masa m (considerada solo en la dirección x) y un muelle lineal de rigidez k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Una banda bimetálica se compone de invar y cobre. The left end of the bimetallic strip is fixed, and the right end is free, loaded by temperature difference. While neglecting self-weight, determine the deflection of the bimetallic strip (free end).
Una estructura de celosía consta de tres barras (una de acero y dos de cobre) unidas por una barra rígida. The structure is loaded by a concentrated force and a temperature difference. While neglecting self‑weight, determine the total deflection of the structure.
Un voladizo de sección rectangular tiene una masa al final. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Una placa rectangular simplemente apoyada está sujeta a diferentes tipos de carga. Assuming only the small deformation theory and neglecting self-weight, determine the deflection at its centroid for each load type.
Este ejemplo es una modificación del ejemplo de verificación 0061; la única diferencia es que el material del recipiente es incompresible. An open‑ended, thick‑walled vessel is loaded by both inner and outer pressure. While neglecting self‑weight, the radial deflection of the inner and the outer radius is determined.
Una barra con una sección cuadrada está fijada en el extremo superior. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.
Este ejemplo sirve como demostración de la coacción del diafragma. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
El objetivo de este ejemplo es demostrar un proceso irreversible causado por la fricción. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
Una consola está cargada por una fuerza concentrada en su extremo libre. Determine the maximum deflection of the console using large deformation analysis.